1990 macgregor 26s sailboat

Owner's Review of the MacGregor 26 Sailboat Models

There is some confusion about all of the different MacGregor 26 models and some controversy about their sailing abilities.

The MacGregor 26 evolved after the Venture 22 and the MacGregor 25, which had been built from 1973 to about 1987. The M25 had a weighted centerboard keel like other trailer able sailboats but featured positive flotation, a low price, easy trailer ability and a comfortable interior with an enclosed head (porta-potty). These features carried forward into M26 models and helped make MacGregor one of the bestselling sailboats.

Differences in MacGregor 26 Models

• The MacGregor 26D (daggerboard), built from about 1986 to 1990, introduced water ballast to replace the weighted keel. When the water was drained for trailering, the boat weighed only 1650 lbs, making it even more attractive for towing with a regular automobile. The daggerboard, like a keel, helps prevent the boat from being blown sideways but could be lifted up for shoal water and trailering.
• The MacGregor 26S , 1990 to 1995, replaced the daggerboard with a swing centerboard (which kicks up in an accidental grounding) and made other smaller changes. Together, the 26D and 26S are often called the "classic" MacGregor 26, and sometimes the 26C. Owners of these earlier models tend to refer to them as "the real sailboats" prior to the changes coming with the MacGregor 26X.
• The MacGregor 26X , 1996 to 2004, marked a major change from the earlier "classic" M26 models by allowing a relatively huge outboard engine that essentially turned the 26X into a powerboat with a mast. Earlier models typically carried outboards as low as 5 or 6 HP (max. 10 HP), but the 26X now took up to 50 HP. For comparison, many thirty-six foot sailboats of this era, displacing more than five times the M's weight, had inboard engines of 25-30 HP. The water ballast could be drained of power, allowing the M26X to come up on a plane like a speedboat. The outboard well had to be moved to the centerline, with twin rudders to each side, and steering changed from tiller to a small powerboat-type steering wheel. The cabin height was increased for greater room inside and the boat is said to sail less well than the earlier 26.
• The MacGregor 26M (motorsailor), 2005 to present, continued the 26X's trend, now allowing up to a 60 HP outboard. The swing centerboard was replaced with a daggerboard to free up more space below and the second tier of windows was added with standing headroom. The boat is advertised to motor at 24 MPH. In addition to the water ballast, there are 300 lbs of permanent ballast, likely needed for stability with so much windage and the high weight of the engine. At 2550 lbs dry (excluding engine), it now needs stronger vehicle and tow package.

Risks and Precautions

Many traditional sailors joke about MacGregors because of the light fiberglass construction (the hull can "oilcan" flex in places if you push hard against it) and its powerboat characteristics since 1996. Many say it is not a "real sailboat." Most misunderstood, however, is the water ballast that has been a hallmark of all twenty-six models.

The water ballast tank is horizontal and only a foot or so beneath the surface, unlike a vertical ballasted keel or centerboard that extends much deeper. Some have even questioned how water, weighing the same as the water displaced by the boat, can be called ballast at all. The ballast tank has been well engineered, however, and does provide righting moment the same as a keel when the boat heels over, because the weight of water far out from the centerline on the "uphill" side (in the air once heeled over) does pull the boat back down the same as a weighted keel.

This does mean that the boat is more tender, or tippy, initially. A story has been told about a sailor on one edge of the deck who grabbed the mast when the boat heeled, and his own weight pulling on the mast that far above the waterline caused the boat to capsize all the way over. Whether true or not, the story illustrates a common perception of how tender the MacGregor is.

It is true that an M26 with 10 people aboard capsized with two fatalities -- most likely due to uneven distribution of the human weight on the boat.

Safely Sail the Water-Ballast

In normal conditions, however, careful sailors can safely sail the water-ballast M26 by following standard precautions:

• Reef sails when the wind is blowing.
• Maintain good balance with crew weight balanced against heeling.
• Prevent accidental gybes.
• Keep the ballast tank full and well-sealed.
• Maintain steerage control at all times.
• Heave to or take other storm action in high wind or waves.
• Don't drink and sail.

The larger safety issue is that for many owners, the M26 is a "starter boat" and they may not have the experience or knowledge to avoid possible problems in time. The bottom line is that anyone who goes sailing needs to be fully aware of the limitations of their boat and practice all safety guidelines.

Experience With the MacGregor 26S

Having owned and sailed a 26S extensively for three years, it indeed sails fairly well and lives up to its reputation of being a roomy and easily trailered pocket cruiser. This sailboat can meet most budgetary needs and has room enough for a family of three to cruise for up to a week at a time.

It is a light boat, but with sailing experience and caution, trouble in winds to thirty knots can be easily avoided. The fiberglass is thin but you can avoid running into rocks. Thousands of MacGregor owners have had experiences where they thoroughly enjoyed sailing.

Keep in mind that it's a light boat and always take the precautions listed above. For powerboat owners of the 26X and 26M, the boat should be as safe as any powerboat but do not hit a rock or another boat at 24 MPH.

Learn the Parts of a Sailboat and How to Communicate Them

Heavy Weather Sailing

Learn How to Sail a Small Sailboat

The Best Beach Tents of 2024, Tested and Reviewed

West Wight Potter 19 Sailboat Review

How to Rig Your Small Sailboat and Prepare to Sail

Review of the O'Day Mariner 19 Sailboat

The 12 Best Inflatable Stand-Up Paddleboards of 2024, Tested and Reviewed

Moscow - Russian Rivers and Waterways Port of Call

The Best Beach in Every State

Tips for Buying a Used Boat for Water Sports

Where to Go in 2023: The Most Exciting Destinations to Explore This Year

The 15 Best Ski Clothing Brands of 2024

The Best Staycation in Every State

Motorhome Test Drive Review of the Winnebago Via 25Q

Greenwich London Day Out

Macgregor 26s

The macgregor 26s is a 25.82ft fractional sloop designed by roger macgregor and built in fiberglass by macgregor yacht corp between 1990 and 1995..

The Macgregor 26s is an ultralight sailboat which is a good performer. It is very stable / stiff and has a low righting capability if capsized. It is best suited as a day-boat.

Macgregor 26s for sale elsewhere on the web:

Main features

Login or register to personnalize this screen.

You will be able to pin external links of your choice.

See how Sailboatlab works in video

We help you build your own hydraulic steering system - Lecomble & Schmitt

Accommodations

Builder data, other photos.

Modal Title

The content of your modal.

Personalize your sailboat data sheet

• Forums New posts Unanswered threads Register Top Posts Email
• What's new New posts New Posts (legacy) Latest activity New media
• Media New media New comments
• Boat Info Downloads Weekly Quiz Topic FAQ 10000boatnames.com
• Classifieds Sell Your Boat Used Gear for Sale
• Parts General Marine Parts Hunter Beneteau Catalina MacGregor Oday
• Help Terms of Use Monday Mail Subscribe Monday Mail Unsubscribe

Buying a 92 Macgregor 26S pro's and cons?

• Thread starter qcovefishing
• Start date Feb 5, 2009
• Macgregor Owner Forums
• Ask A Macgregor Owner

qcovefishing

I am thinking of buying a 92 Macgregor 26S and am new to sailing. I have been around boats all my life and spent most of my family vacations in BC fishing. I enjoy being out on the water but have very limited sailing experience. Is a Macgregor 26S a good boat to learn on and how does it differ from the 26's with the large engines?  

I have a 92 26s. I like it alot. It is 26 feet long but seems as easy to rig and sail as my 15' Mutineer that my wife and I race (for fun). Things I like about the 26s -Draft is only 15", can go in shallow water -water ballast means it is light to trailer, pull with smaller vehicle like my mini van. -like the place for the outboard and my 5hp pushes it ok. -the queen bed in nice -I had a Mac 25 with 600# cast iron keel, sailed fine but didn't like the maintenance on the keel, my 26s has a light swing keel that requires no painting and it tucks all the way into the hull so it can be beached easily. -One time I got stuck in shallow water in my 26s I blew out some ballast and then just got out and pushed it easily off and away we went. -The 26s sails fine. You can sail it on the main sail at first or when it is pretty windy. -I like the 26s kick up rudder assemble. -The newer 26x and m are nice too, but they are more of a motor boat and less of a sailboat. They go faster with the bigger motor for sure.  

I agree with everything Jansen said. For me, the biggest pro is the easy trailerability and and ease of set up. The nearest lake is almost 2 hours away from here. If I was keeping it at a dock or mooring, I might choose differently, but in my price range there is no other boat this size that can do all that the 26C's do. On the con side, the water ballast makes them more tender than a comparable keel ballasted boat. They heel quickly but stiffen up as the water ballast tank starts to rise out of the water on the windward side. I haven't heard any stories about anyone on this forum ever tipping one over. Right off the production line, there are few frills provided with these boats, but most owners add lots of upgrades. Chances are that the previous owner has added lots of goodies for you. I think it has been a great boat to learn on, and I have learned lots from the boat and this forum. If you buy it, you will find a wealth of friendly info here. Good Luck!  

Modesto-Mike

I have a 92 26 Classic with swing keel. We have had it for a little more than a year and really enjoy it. We sail it in San Francisco bay. It is a little small for the big wind days, but we do fine. We have rigged a reef line and added a topping lift which makes it easier to sail. We enjoy it because we can trailer it home and save on the slip rental. We have done one overnighter on it so far. Stayed on the moorings in at angel island. Had a great time. They are great boats. Don't hesitate to buy one.  

I cannot think of any cons in buying this boat and the pros have been well explained by the other respondants. I have been boating most of my life and have actually gone from a 27 ft keel boat to a 93 mac 26s. I sail solo most of the time and regularly participate in club racing against other boats of similar legnths with very satisfying results. Have also done many comfortable weekend cruises as well in the waters around South Australia. This boat can be very well set up and personalised to your own liking with many great helpful ideas from this website. Happy shopping, Kev  

Noticed your in seattle did you see this boat on craigs list? There was one with pics on there a few days ago. Looked like a very nice boat.  

I have a 93S that I moor on a N. Idaho lake and often spend the w/e on it. Great boat, sails as well as any I have been on - I would buy another in a minute. If you get this way - look me up - should have it in the water by early April.  

I too agree with the others. I doubt you'll find many people on this forum who have much negative to say about this boat. For its purpose - a relatively large, inexpensive trailerable boat with shallow draft that sails well - it's hard to beat. I guess that the biggest negative is the compromises that were made to achieve the above: it's not designed for offshore passages or prolonged exposure to rough seas and wind. But so what? You don't need to make passages when you can trailer it to your destination(s).  

Yes I noticed that one but the one I am looking at is elswere and would require some travel to pick up. If it does fall through I am going to take a closer look at the one near bellingham.  

and....compared to the M or X = powersailors ? the original question... -both the large motor boats are quite different in many ways. notiably the big motor and ability to do 20-25knts. but at a price. for some the powersailors ARE better.... most here own the older, less expensive classic sail only type of mac. you'll need to search power sailor to understand the difference... GL!  

My biggest complaints about my '92 26S are headroom and stowage. I'm constantly working on the stowage issue, can't do anything about the headroom but learn to duck. Both issues are counter to what the Mac was designed for, easy trailerability, so you either learn to accept it or find another boat.  

I have a 92 S and love it! My family and I (5 of us) tour the Gulf Islands, and San Juans in ours, and although a little tight, we live and sleep happily on board. She has held up in rough passages, and is a pleasure to sail when the wind is 5-20. I can't say enough about what a great boat this has been for the money. We opened up the area's below the seats and V-birth for better storage access. And put a plexiglass window into the forward hatch, to give light upfront. That made a huge difference in the feeling down below. Roller furling is a must, so you can reef when the wind picks up. Don't hesitate to buy one.....There great!  

• This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies. Accept Learn more…

• New Sailboats
• Sailboats 21-30ft
• Sailboats 31-35ft
• Sailboats 36-40ft
• Sailboats Over 40ft
• Sailboats Under 21feet
• used_sailboats
• Apps and Computer Programs
• Communications
• Fishfinders
• Handheld Electronics
• Plotters MFDS Rradar
• Wind, Speed & Depth Instruments
• Anchoring Mooring
• Running Rigging
• Sails Canvas
• Standing Rigging
• Diesel Engines
• Off Grid Energy
• Cleaning Waxing
• DIY Projects
• Repair, Tools & Materials
• Spare Parts
• Tools & Gadgets
• Cabin Comfort
• Ventilation
• Footwear Apparel
• Foul Weather Gear
• Mailport & PS Advisor
• Inside Practical Sailor Blog
• Activate My Web Access
• Reset Password
• Customer Service

• Free Newsletter

Ericson 34-2 Finds Sweet Spot

How to Sell Your Boat

Cal 2-46: A Venerable Lapworth Design Brought Up to Date

Rhumb Lines: Show Highlights from Annapolis

Solar Panels: Go Rigid If You have the Space…

Leaping Into Lithium

The Importance of Sea State in Weather Planning

Do-it-yourself Electrical System Survey and Inspection

When Should We Retire Dyneema Stays and Running Rigging?

Rethinking MOB Prevention

Top-notch Wind Indicators

The Everlasting Multihull Trampoline

What Your Boat and the Baltimore Super Container Ship May Have…

Check Your Shorepower System for Hidden Dangers

DIY survey of boat solar and wind turbine systems

What’s Involved in Setting Up a Lithium Battery System?

The Scraper-only Approach to Bottom Paint Removal

Can You Recoat Dyneema?

How to Handle the Head

The Day Sailor’s First-Aid Kit

Choosing and Securing Seat Cushions

Cockpit Drains on Race Boats

Re-sealing the Seams on Waterproof Fabrics

Safer Sailing: Add Leg Loops to Your Harness

Waxing and Polishing Your Boat

Reducing Engine Room Noise

Tricks and Tips to Forming Do-it-yourself Rigging Terminals

Marine Toilet Maintenance Tips

Learning to Live with Plastic Boat Bits

• Sailboat Reviews

MacGregor 26 (newer model)

This hybrid powersailer is so popular that the company has a year- long backlog of orders. its an inexpensive entry level sailboat also capable of towing a water skier..

MacGregor Yachts, one of the largest builders in the US, has a well-established reputation as the producer of inexpensive boats. Located in Orange County, California, its plant sits across the street from the former headquarters of Westsail and Islander in a neighborhood that in 1973 built more than 24,000 boats with a retail value of $88 million. A year later, the number of boatbuilders shrank from 46 to 22. MacGregor endured by sticking to a business plan that is strong on financial and management principles and devoid of romance.

The company was founded by Roger MacGregor as a hobby following his successful completion of the MBA program at Stanford University, where he graduated Phi Beta Kappa, second in a class of 200; he had previously graduated Phi Beta Kappa with a degree in economics from Occidental College.

MacGregors studies at Stanford produced a business model based on the sailboat industry that he eventually used as the blueprint for the company. In 1964, while employed at Ford Aerospace, he began building boats as a hobby. Wife Lou, who is still active in the business, oversaw the embryonic stages of the company.

In 1967, when I was finally making more money from the hobby than my real job, I moved into boatbuilding full time, he recalled.

Since that modest beginning the company has built more than 37,000 boats in its 65,000-square-foot factory, and has annual sales of $10 million. It employees 150 people.

Initially marketed under the Venture brand, the name was changed to MacGregor in 1977. Though the company focused on 22- to 25-foot fiberglass sloops, it made a foray into the big boat market in the 1980s with the MacGregor 65 ULDB, which MacGregor claims was the most successfully produced big boat in the industry. A decade earlier, MacGregor built a 36′ catamaran.

Unlike many industry doomsayers, MacGregor doesn’t agree that the sailboat market has dried up; he thinks people have lost interest because of a perception that sailing is too complicated. To attract newcomers to the sport, he builds boats that are simple to operate, require little maintenance, and are low-priced. His 28-page owners manual is written in everyday English, and includes basic sailing instructions. He also has recruited a loyal dealer network that understands the product and caters to first-time buyers.

MacGregors strategy is to concentrate the entire production effort on one boat so as to amortize production and tooling costs over a long run.

Over the years we have zeroed in on the 26-footer for a number of reasons. It is the largest boat that can be easily and safely trailered and launched, and economically shipped in containers.

Originally introduced as the 26X, the new model replaced an earlier MacGregor 26, a water-ballasted sloop previously reviewed in PS (November 1, 1987 and August 1, 1995); 7,000 of the first model were produced. Since its introduction in 1995, 4,000 of the new 26s have been built, and the company enjoys a backlog of orders stretching into 2001. MacGregor sees no need to increase production, which currently turns out one boat every two hours.

The Design The 26X, conceptually similar to the powersailers built by Lancer in the 1980s, represents MacGregors attempt to reach several markets with a boat capable of sailing at 7 knots and powering at 20-plus knots.

From an aesthetic standpoint, the boat gets average marks. Viewed from the bow, with an entry angle of 18, it has a conventional appearance. Viewed from the beam, its high topsides are evident. Freeboard amidships is 3′ 5″.

Unlike the rounded sections of her predecessor, the new model has a flat, straight bottom designed to enhance planing while under sail or power. It also has a harder turn of the bilge, which translates to a higher initial righting moment. Some owners say the boat will carry a genoa in 15-18 knots of wind before reefing the main or shortening the headsail.

The boat displaces 3,750 lbs. with full tanks; the sail area/displacement ratio (SA/D) is 19 and the displacement/length ratio (D/L) is 138, which indicate the potential for speed.

However, MacGregor says, these figures don’t mean much because crew and gear weight is such a big part of the all up weight. He said that every 100 pounds of weight in the boat reduces speed under power by one mile per hour.

Construction MacGregors theory is that he can sustain his success by eliminating inconsistencies and waste from the production process. Fiberglass fabrics used in the lay-up are cut in patterns and bundled in sequence for laminators.

The hull, deck and interior liners are solid, hand-laid fiberglass, and MacGregor brags that theres not a chopper gun in the factory; instead, workers use low-volume airless guns to wet out resins. No cores are used.

He is particularly rankled by critics who claim his methods are quick and dirty.

We have the neatest, most tightly controlled plant on the earth, and these boats arent failing, he said.

The lamination schedule calls for a layer of 1-oz. mat, followed by 10-oz. cloth, a layer of 1.5-oz. mat, 24-oz. roving, and layers of 1.5-oz. mat and roving. High-load areas in the centerboard trunk and bow have 15 layers of fiberglass built to a thickness of 3/4″; low-load areas are 3/16″-3/8″ thick.

The hull-deck joint is two outward-turning flanges that are secured with stainless steel bolts and locknuts with nylon inserts located on 4″ centers. The joint is bonded with 3M 5200 and the seam is covered with a rubber rail.

The liners are bonded to the hull with 6″ wide strips of mat and roving.

Boats built since spring 1999 have a new deck structure. Older boats have a balsa-cored deck and companionway hatch. The new deck is stiffened by a series of solid fiberglass U-shaped beams with an outer flange bonded to the inside of the deck. The beams, which are on 4″-6″ centers, are filled with foam, over which are laid layers of 1.5-oz. mat; the deck liner is then laid over the deck, which compresses the foam and bonds the deck and liner.

MacGregor said the new method produces a stronger structure and avoids the problems of rot with balsa. The process also reduces weight by 125 lbs.

Water ballast is carried in a chamber that runs from 3′ forward of the transom to the V-berth; it is 4′ wide and acts as a longitudinal stringer. It is enclosed by a fiberglass module bonded to the hull.

This leaves precious little area below the sole for a bilge. Because there is no way to inspect the bilge without looking behind the galley, there is no way of knowing how much water is in it. The company now drills a 1/2″ hole in the sole below the companionway to allow bilge water to appear on the floor of the main cabin.

Without the hole it is possible for the boat to collect a really large, stability-threatening load of bilge water, MacGregor said. Since the liner floor area is essentially a watertight tub, the skipper had no way of knowing until it reached the level of the cutout in the face of the galley.

I prefer a more obvious warning. When he steps in the cabin and ends up with water up to his ankles he will get the message. I recommend owners of older boats make a similar hole, being careful not to drill into the water tank.

One owner said cleaning up bilge water on the sole is messy.

A company video shows that, will full ballast tanks, the boat is self righting. With 120 lbs. of pressure on the jib halyard, the mast lay in the water, and immediately popped upright when the halyard was released; MacGregor said the limit of positive stability is about 115.

MacGregor also claims the boat has positive flotation; the same video shows a boat still floating that is filled with water halfway up the cockpit floor. Flotation is Styrofoam blocks in the cockpit coaming, bow, and under the anchor locker.

As weve written before, water ballast doesn’t produce as stiff a boat as lead, but because you can drain it on the ramp (or dump it underway going 8 knots or faster), you don’t have to tow it down the road.

The centerboard is hollow with drain holes, the bottom of which is filled with resin. It weighs 25 lbs., compared to 600 lbs. in the original 26. The board retracts into the hull, thus avoiding potential damage while launching and loading.

Access to deck hardware and wires is via liner plugs mounted throughout the boat; access to the motor mount and rudder mount are through a hatch in the stern.

The mast is a 7/8 fractional rig with swept-back spreaders and two shrouds; spreaders are mounted in sockets on the mast, an improvement over the original 26. MacGregor constructs the spar from 3″ x 4″ extrusions with wall thicknesses of 1/8″. Standing rigging is 1/8″ 7 x 19 wire on the stays, and 5/32″ 1 x 19 for the shrouds.

Despite criticism that the rigging is too light, MacGregor said, These rigs just don’t come down.

Chainplates are bolted through the hull with stainless steel bolts, washers and nuts. They are strong enough that during construction they are used to remove the hull from the mold;

Deck The cockpit and deck are typical of boats this size; however, there are no side decks so movement forward is over the cabintop. There are lifelines running from the stern pulpit to the base of the bow pulpit; owners with small children would be well-advised to install safety netting at the bow.

Deck hardware consists of two Lewmar #6 winches and cam cleats for the centerboard and furler lines, vang and halyard, located atop the cabin. The centerboard raises easily from the cockpit.

The helm is a movable seat on the transom behind a steering pedestal; cockpit seats are more than 6′ long, and wide enough to be comfortable for most adults.

Because of its size, the small stainless steel steering wheel looks out of place in the cockpit; however, it is reachable from the helmsmans seat, or the rail.

The mainsheet terminates at a padeye atop a stainless steel pipe inside the pedestal. Though the mainsheet arrangement is convenient to the helmsman, we think a sailor intent on proper sail shape will be frustrated.

MacGregor disagrees. The vang (a $69 option) will control the leech adequately.

The boat is equipped with twin rudders, which improves handling when heeled, and provides space on the transom for up to a 50-hp. motor. The rudders raise easily with ropes cleated on the transom.

The motor is raised electrically from controls on the steering pedestal. One boat we inspected had the cables hidden under a polypropylene strip on the cockpit sole, and on another boat they were led through a hole in the side of the cockpit aft through the stern.

A stainless steel rod attached to the rudders and the front of the motor allows moving them simultaneously.

We were alarmed at the location of the factory-installed stern ladder, which is mounted between the port rudder and the engine, close enough to the engine propeller to be a hazard. Todd McChesney of Bluewater Yachts in Seattle, with whom we sailed, installs a ladder fabricated in Seattle that is mounted outboard of the rudder, a better alternative.

Accommodations The area belowdecks feels spacious, a reflection of the 90″ beam, lack of bulkheads or visual intrusions, shiny gelcoat surfaces that are devoid of any wood trim, and reasonable headroom. The company advertises standing headroom. We measured 510″ headroom at the foot of the companionway, but theres less amidships.

Accommodations include a king-sized berth below the cockpit, galley and two settees to port, head and dinette to starboard, and V-berth large enough for two adults.

Though the boat is advertised as having sleeping accommodations for six, MacGregor says thats two too many. The aft berth measures 90″ x 78″, and has enough headroom to use the hull as a backrest. The forward V-berth is 76″ wide at the head, and the dinette converts to a double that measures 80″ long and 41″ wide.

Except for a smoked Plexiglas door enclosing the head, the entire area is wide open, so privacy curtains fore and aft would be high on our list of additions.

The dinette is elevated, providing virtually 360 sight lines through fixed ports, forward hatches and the companionway hatch-a good touch. The table, which is nearly 36 inches square, has a clever feature-a clear acrylic insert flush with the surface of the table under which a chart can be placed. The aft dinette seat is 41″ wide and 18″ deep; the forward seat is slightly smaller.

Stowage below the forward seat extends to the V-berth, and stowage for a removable 48-quart ice chest is located below the aft seat.

The head is marginally large enough to allow showering. It is 25″ wide, 40″ long, and has 57″ of headroom. The only furnishings are a molded sink, small storage area, and a mirror on the bulkhead. A porta-potty is equipped with a holding tank.

The galley is quite small. Counter space consists of several 4″ x 5″ ceramic tiles, a molded fiberglass sink with a freshwater faucet, and cutout for an optional two-burner stove. The galley could use more stowage.

The finish of stowage areas isn’t great; we found rough surfaces on the hull as well as fiberglass shards that can produce cuts.

Performance We tested the boat on a dead calm day so were able to try her agility under power. We had to rely on owner comments for input about sailing characteristics.

Because of its high profile and hull shape, upwind performance is average at best. Most owners opt for a CDI roller furler, a $495 option.

I usually allow 95-105 for a tack, the owner said. Absolute perfect sailing is in 10-15 knots of wind on a close reach. Ive sailed the boat in as much as 35 knots with reduced sail.

Gene Arena, a dealer who has represented MacGregor in San Francisco since 1968, said the boats fare well in the bays gusty, lumpy conditions.

We have to reef this boat sooner than a typical 25′ keel boat, he said, but even novices learn to sail the boat quickly. We typically put the first reef in when wind speed reaches 15-20 knots; when wind speed exceeds 25 knots we tuck in the second reef and reduce the headsail to 65%.

The calculated jib sheeting angle is 11, but Arena said, I don’t think this boat points as well as the old 26 because it has more windage and a different hull shape, so the best bet is to foot off 10.

An owner who sails regularly on San Francisco Bay said, My wife and I sail the boat regularly in 20-knot winds with no problems. With a reef in the main, shes stable and sails well, heeling about 15. But Id never take her into blue water.

Another owner, who sails off the coast of Northern California, said, We typically have 15-20-knot winds, and long 8′-10′ swells, which she handles easily. I think this is an outstanding boat. I was knocked over 50 by a 40-mile per hour gust, and she popped right up and nothing broke.

A Puget Sound sailor, who said he usually sails the boat under shortened sail, records speeds of 8 knots on a broad reach with the genoa. I also like the fact that the bigger motor allows me to fight the heavy current we experience in the Northwest, he said.

The PHRF handicap is between 240 and 250.

MacGregor claims top speed under power exceeds 20 knots, which we confirmed on our test with a boat powered by a 50-hp. outboard. A 9.9-hp. will push the boat at 6-7 knots, a 25-hp. at 12-14 knots. Most buyers opt for the 50-hp. motor. But the added weight of the big outboard has its downside. One owner said, The boat ends up with too much weight aft with 180-230 pounds of motor on the stern, ballast tank, gas tanks, and passengers.

In addition to straight-ahead speeds, we made 360 turns at 18 knots with relative ease and noted that the boat stays relatively flat. In choppy seas, the flat bottom could be expected to pound.

As for its seaworthiness, Roger MacGregor said, The 26 was designed for typical small cruising boat use-inland waters and limited coastal sailing. It is too small to be a long-distance passagemaker. It wont hold enough gear and supplies, and the long-term, day-after-day motion of a small, light sailboat can be tough on the crew.

There are thousands of these boats out there, and many have been caught in, and survived, some really extreme weather conditions, on both lakes and oceans. Like most small cruising sailboats, the 26 can handle high winds and nasty seas, but risk and discomfort levels increase dramatically in severe weather. To maximize fun and safety, most of our owners wisely keep a watchful eye on the weather and try to avoid severe conditions.

Conclusion Theres no question MacGregor is building an inexpensive product that sells for $4,000-$6,000 less than its primary competitors. The list price for boat, sails and trailer is $14,995 FOB the factory. Genoa and gear, roller furling, cruising spinnaker, vang, mast raising system, stove, cushions and transportation jump the price to $17,000; add $5,000-$7,000 for engine and electronics.

They also enjoy relatively high resale. Two-year-old boats on the market are selling for 85%-90% of their original prices.

The owner of a recent model sums it up well, She is fast enough to be pleasurable, forgiving enough that I can be stupid, balanced enough that I can be lazy.

The two-year warranty covers all parts manufactured by MacGregor.

Contact- MacGregor Yacht Corp., 1631 Placentia, Costa Mesa, CA, 92627; 949/642-6830.

RELATED ARTICLES MORE FROM AUTHOR

I’d like to add that my MacGregor 26 M has as much room as some 35 footers. I bought it new in 2006 and I will never tire of it! It is the “Jeep” of sailboats, it can float in 12″ of water, and can drive right up on the beach. With a 4-stroke Merc 60 hp, she’ll do 21 mph fully loaded (actually overloaded). She’ll get up on a plane and you’re gone, baby! And at terrific fuel mileage. She sails ok but you won’t win any races, however it wins points being able to sail on a beautiful sunset evening, with nothing but music and no engine noise. She is amazing and people are curious to see how it functions and love it. In Puget Sound the weather changes quickly, but you can get home or back to safe harbor lickity-split, Thank you Roger MacGregor! Mike Jones “Antares”

There is so much information to read I’m wondering if the information to be processed is still relevant. I learn so much about the Mac Gregor 26. This sailboat sounds to amazing to be true in todays market prices. Just starting to to research and there are a lot of older ones out there for sale. Millions dollar question -wait and get new or get old to learn as I go knowing a boat will be more costly so I have to have some throw-away cash on the side

LEAVE A REPLY Cancel reply

Log in to leave a comment

Latest Videos

40-Footer Boat Tours – With Some Big Surprises! | Boat Tour

Electrical Do’s and Don’ts

Bahamas Travel Advisory: Cause for Concern?

Island Packet 370: What You Should Know | Boat Review

• Privacy Policy
• Do Not Sell My Personal Information
• Online Account Activation
• Privacy Manager

You are using an outdated browser. Please upgrade your browser to improve your experience.

• MacGregor Boat Parts
• Tattoo Boat Parts
• Venture Boat Parts
• MacGregor and Venture Trailer Parts

Centerboard

Convenience & Safety

Engine Parts

Hull Hardware

Mainsail Handling

Miscellaneous

Railings & Ladders

Sailing Performance Upgrades

Specials / Used Products

Tools & Maintenance

• Vessel Reviews
• Passenger Vessel World
• Offshore World
• Tug and Salvage World
• Maritime Security World
• Specialised Fields
• Marine Projects World
• Small Craft World
• Tanker World
• Dry Cargo World
• Boxship World
• Aquaculture World
• Trawling World
• Longlining World
• Seining World
• Potting World
• Other Fishing Methods
• Regulation & Enforcement
• Feature Weeks
• Classifieds
• Book Reviews

VESSEL REVIEW | Sinichka – Electric commuter boats designed for Russia’s Moskva River

A series of three new electric monohull commuter ferries have already begun operational sailings on the Moskva River in the Russian capital Moscow.

Built by Russian shipyard Emperium, sister vessels Sinichka , Filka , and Presnya – all named after rivers in Moscow – are being operated by the Moscow Department of Transport and Road Infrastructure Development (Moscow Deptrans). They are the first units of a planned fleet of 20 vessels that will serve the capital city and other nearby communities. The new ferry system will be the water transport system to be operated on the Moskva River in 16 years.

Each vessel has a welded aluminium hull, an LOA of 21 metres, a beam of 6.2 metres, a draught of only 1.4 metres, a displacement of 40 tonnes, and capacity for 80 passengers plus two crewmembers. Seating is available for 42 passengers on each ferry, and the main cabins are also fitted with USB charging ports, wifi connectivity, tables, toilets, and space for bicycles and scooters. The cabin layout can be rearranged to allow the operator to adjust the distances between the seats and to install armrests of varying widths.

An open upper deck is also accessible to passengers and is the only area on each ferry where smoking is allowed.

The ferries are all of modular construction with each ferry’s wheelhouse, main cabin, and other structural elements being built as complete, separate components. This enables the ferries to be easily dismantled for transport to anywhere in Russia by rail and then quickly re-assembled within seven days.

The ferries are also ice-capable. Recently completed operational trials on the Moskva showed that the vessels can also easily navigate under mild winter conditions with broken surface ice, though year-round operations are planned for the entire fleet.

The ferries are each fitted with 500kWh lithium iron phosphate battery packs that supply power to two 134kW motors. This configuration can deliver a maximum speed of 11.8 knots, a cruising speed of just under 10 knots, and a range of 150 kilometres.

Emperium said the transfer of rotation of electric motors to the propeller is carried out by direct drive. As a propulsion installation, a pulling rotary propeller-steering column with double screws is used. The installation of double pulling screws, with similar power, allows an operator to increase the efficiency of the propulsion system to deliver a slightly higher speed or to reduce energy consumption. This arrangement also provides the ferries with enhanced manoeuvrability necessary for navigating in close quarters.

The batteries themselves have projected service lives of 10 to 12 years and are fitted with safety features such as built-in fire extinguishers and gas vents. Quick-disconnect features allow the batteries to be easily removed for replacement or maintenance.

Some of our readers have expressed disquiet at our publication of reviews and articles describing new vessels from Russia. We at Baird Maritime can understand and sympathise with those views. However, despite the behaviour of the country’s leaders, we believe that the maritime world needs to learn of the latest developments in vessel design and construction there.

Click here to read other news stories, features, opinion articles, and vessel reviews as part of this month’s Passenger Vessel Week.

Related Posts

Baird Maritime

Tags: Emperium Filka Moscow Moscow Department of Transport and Road Infrastructure Development Moskva River Presnya Russia Sinichka WBW newbuild

• Previous VESSEL REVIEW | Ferry Rokko – Second 194m Ro-Pax for Miyazaki Car Ferry
• Next Brighton man to be charged for illegal abalone haul

Baird Maritime , launched in 1978, is one of the world's premier maritime publishing houses.

The company produces the leading maritime new portal BairdMaritime.com , home of the world famous Work Boat World, Fishing Boat World, Ship World, Ausmarine, and Commercial Mariner sub-sites, and the industry-leading ship brokerage platforms WorkBoatWorld.com and ShipWorld.com .

Contact us: [email protected]

© Copyright - Baird Maritime

• Terms & Conditions
• Advertise with Baird Maritime
• Submit News/Leads

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

• Sailboat Guide

1990 MacGregor 26s

• Description

Seller's Description

Specs: - MacGregor 26s 1990 model. 3rd owner. I purchased in 2015 from MS. - Original steel trailer with new tires and lights. Bearings lubed regularly. Pulled 4hrs on multiple occasions with no issues. - 9.9 Hp Honda 4 stroke. Manual start. Runs great. - Original main and jib. Purchased a 130 Genoa which is currently on CDI flexible furler rig - New bimini top - Tiller tamer installed - New navigation lights on hull and mast - 70AH battery system with onboard charger and battery isolation switch - LED lights in cabin - 12 gal freshwater system with pressure activated 12v sink faucet - 5 gal porti potti - single burner portable propane or butane stove - memory foam mattresses for berths - shore power outlet and 50’ cordset. 3 120v AC outlets on board - 6000btu air conditioner included with custom companionway seal - pop top cover and table original to boat are in good shape - Anchor setup included

Equipment: Specs: - MacGregor 26s 1990 model. 3rd owner. I purchased in 2015 from MS. - Original steel trailer with new tires and lights. Bearings lubed regularly. Pulled 4hrs on multiple occasions with no issues. - 9.9 Hp Honda 4 stroke. Manual start. Runs great. - Original main and jib. Purchased a 130 Genoa which is currently on CDI flexible furler rig - New bimini top - Tiller tamer installed - New navigation lights on hull and mast - 70AH battery system with onboard charger and battery isolation switch - LED lights in cabin - 12 gal freshwater system with pressure activated 12v sink faucet - 5 gal porti potti - single burner portable propane or butane stove - memory foam mattresses for berths - shore power outlet and 50’ cordset. 3 120v AC outlets on board - 6000btu air conditioner included with custom companionway seal - pop top cover and table original to boat are in good shape - Anchor setup included

Rig and Sails

Auxilary power, accomodations, calculations.

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

SA/D = SA ÷ (D ÷ 64) 2/3

• SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D : Displacement in pounds.

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Ballast / Displacement * 100

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )

• D: Displacement of the boat in pounds
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

CSV = Beam ÷ ³√(D / 64)

Dry boat weight: 1650 lbs. Centerboard weight: 50 lbs. An earlier model, called the MACGREGOR 26D was similar but with a (vertically) lifting keel. (also with water ballast = reduced weight for trailering. Not to be adjusted while sailing). Spinnaker area: 360 sq. ft. Thanks to a number of Macgregor owners for providing corrections and updated images.

This listing is presented by SailboatListings.com . Visit their website for more information or to contact the seller.

View on SailboatListings.com

Embed this page on your own website by copying and pasting this code.

Similar Sailboats For Sale

1990 MacGregor 26S

1992 MacGregor 26S

1990 Macgregor 26S -- Swing Centerboard

• About Sailboat Guide

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.